BD Rebuilder Beta - Bug Reports Only

[GaPony]

I'm not sure what that has to do with Blu-Ray movies.... Maybe you need to reinstall WMP or install WMP 11, if you didn't have it before...and stop tweaking stuff.

[Jake802]

It has to do with my earlier posts I was having issues getting BD-RB to work, and I couldn't come up with an answer why.JDobbs, referred me to a link with some solutions.I used one and it appeared to work but now I have no audio when playing avi files in wmp,and I was wondering if anyone here knew why,no need for you to be rude.

[GaPony]

I wasn't being rude... just to the point. You've been running Windows 7 with no problems until you ran into some VC-1 stuff. You changed ffdshow to wmv 9, when you maybe should have left it disabled (or set it to disabled) and installed Windows Media Player 11, if you didn't already have it installed and set up. I run this on a PC with Win 7 64-bit, another with Win 7 32-bit, and my main PC with Vista 64-Bit. All I did was follow JDobb's instructions for installing the assiciated software (ffdshow, Matroska Splitter, avisynth, etc.) and haven't had a single issue that wasn't effecting everyone else. I know turbojet said the WMP 11 codec didn't work outside of WMP, but something is doing the job.

It sounds like somewhere in the tweaking process you replaced a WMP audio codec with something else, but either doing a system restore to before the tweak, or reinstalling Windows Media Player would likely fix that problem. You weren't clear on the nexus between playing the AVI file and BD-Rebuilder, but I went back and looked at your posts and think I see where it went wrong. I don't have any of the problems turbojet was talking about in his post. I have TMT installed on the Win 7 32-bit and Vist 64-bit PCs, but not on the Win 7 64-bit PC and still no problems. Maybe I've just been lucky to avoid the problematic interlaced video files.

[kanerulz69]

i did watchmen and it ran fine but it doesnt play the movie nor / title scenes or anything else, but the disc is full is it a bdr issue? and yes i tried it on my sony s350 player and computer using powerdvd and total media theatre 3 platinum, it plays the blu ray title scenes at the beginning / trailer scene etc

nevermind i figured out it was dvdfab that was the problem using there bluray to hard drive and when i used anydvd it worked perfect, i figured i'd give theres a try and see how it worked since i always use anydvd hd and dvdfab is alot ALOT faster but not guaranteed to work perfect like anydvd hd

[Jake802]

I wasn't being rude... just to the point. You've been running Windows 7 with no problems until you ran into some VC-1 stuff. You changed ffdshow to wmv 9, when you maybe should have left it disabled (or set it to disabled) and installed Windows Media Player 11, if you didn't already have it installed and set up. I run this on a PC with Win 7 64-bit, another with Win 7 32-bit, and my main PC with Vista 64-Bit. All I did was follow JDobb's instructions for installing the assiciated software (ffdshow, Matroska Splitter, avisynth, etc.) and haven't had a single issue that wasn't effecting everyone else. I know turbojet said the WMP 11 codec didn't work outside of WMP, but something is doing the job.

It sounds like somewhere in the tweaking process you replaced a WMP audio codec with something else, but either doing a system restore to before the tweak, or reinstalling Windows Media Player would likely fix that problem. You weren't clear on the nexus between playing the AVI file and BD-Rebuilder, but I went back and looked at your posts and think I see where it went wrong. I don't have any of the problems turbojet was talking about in his post. I have TMT installed on the Win 7 32-bit and Vist 64-bit PCs, but not on the Win 7 64-bit PC and still no problems. Maybe I've just been lucky to avoid the problematic interlaced video files.

I did this as well, I ran into and issue with Watchmen,and I hadnt changed anything until it was suggested. It didn't work,I didnt, WMP was aleady installed when Windows 7 installed which hasnt been a problem ever,So I then did a restore taking off any FFDShows I had,Installed FFDShow 64Bit like I had on the computer and it still wasn't working,I then read JDobbs suggestion pointing me to that thread,That's where my tweaking started and I ran into the issue with the WMP.Everything else seemed find but I played my backup copy of watchmen and it skipped once or twice so I may just reformat everything and start from square one.Sorry your post just seemed rude or rude in nature when I was just asking to see if anyone else encountered the same issue and may now how to fix. I apologize if I took it the wrong way.

[Chiamos]

I hear you, and am in agreement.
I am prepared to disable McAfee while running BD-RB, and this seems like the most logical choice. I rarely surf the internet or do anything else while backing up a movie, so it should be little risk for me.
Do you want to know and have it reported if McAfee is deleting BD-RB?

Rather than disabling or even removing the antiviral program, as you may have an option to set an exception for BD-RB in the antiviral scan and guard configuration, so the warning and auto quarantine will not occur.:rolleyes:

[daberti]

McAfee just updated again and now BD-RBV02602 is removed/quarantined. This has become a real nuisance.

Read my post above to learn how to address once and for all this issue.

In short:
1)Go to notepad and open a new text file and name it as artemis_workaround.reg

2)Paste what is just below:
[HKEY_LOCAL_MACHINE\SOFTWARE\McAfee\VirusScan\Artemis\On Access Scanner]
"ArtemisAllowed"=dword:00000001
"ArtemisEnabled"=dword:00000001
"ArtemisLevel"=dword:00000000

3)close and save the file

4)Via explorer double click on file

5)Shutdown PC

6)Start pc

Let me know it this solves

[daberti]

Rather than disabling or even removing the antiviral program, as you may have an option to set an exception for BD-RB in the antiviral scan and guard configuration, so the warning and auto quarantine will not occur.:rolleyes:

See my hint above. You'll easily notice that noting is dsabled.
Just need to set the proper OAS treshold for McAfee's Artemis action.

[jdobbs]

Once again posting to correct for McAfee's Artemis engine false positive.- Recompiled to prevent false positive for "Artemis"
in McAfee. Same as was necessary in v0.26.02.
- Other minor corrections and cosmetic fixes.

[GaPony]

I did this as well, I ran into and issue with Watchmen,and I hadnt changed anything until it was suggested. It didn't work,I didnt, WMP was aleady installed when Windows 7 installed which hasnt been a problem ever,So I then did a restore taking off any FFDShows I had,Installed FFDShow 64Bit like I had on the computer and it still wasn't working,I then read JDobbs suggestion pointing me to that thread,That's where my tweaking started and I ran into the issue with the WMP.Everything else seemed find but I played my backup copy of watchmen and it skipped once or twice so I may just reformat everything and start from square one.Sorry your post just seemed rude or rude in nature when I was just asking to see if anyone else encountered the same issue and may now how to fix. I apologize if I took it the wrong way.

That might not be a bad idea... who knows what might have gotten "tweaked" along the way... I'm not using 64-bit bit versions of anything...just the 32-bit programs pointed to in the first post here. Maybe The Watchmen isn't the best movie to judge by. I've seen several posts referenceing that movie where problems had not been encountered by the person with other movies. I don't have it, so I couldn't tell you if I had problems with it. I do have a pretty strict policy of "When in doubt, make a movie only copy". :)

[daberti]

Once again posting to correct for McAfee's Artemis engine false positive.- Recompiled to prevent false positive for "Artemis"
in McAfee. Same as was necessary in v0.26.02.
- Other minor corrections and cosmetic fixes.

probably you may wish to avoid the hassle of recompiling again and again just by means of adding the .reg file to the package, to be run before file copying.
Just my thought though.

[jdobbs]

probably you may wish to avoid the hassle of recompiling again and again just by means of adding the .reg file to the package, to be run before file copying.
Just my thought though. People get pretty upset when you make mods to their system -- especially those related to security. I think this just points out a weakness of McAfee's Artemis system. I wonder if there are ways for companies to disable their competition (or software they don't like) by electronically reporting their signatures as "trojans" -- and causing McAfee to remove their executables?

Something to think about, eh?

[Capsbackup]

People get pretty upset when you make mods to their system -- especially those related to security. I think this just points out a weakness of McAfee's Artemis system. I wonder if there are ways for companies to disable their competition (or software they don't like) by electronically reporting their signatures as "trojans" -- and causing McAfee to remove their executables?

Something to think about, eh?

jdobbs, you may be on someone's radar!:rolleyes:

[jdobbs]

jdobbs, you may be on someone's radar!:rolleyes:It makes a nice conspiracy theory anyway. :) It lines up nicely with the contention that BD-RB was seen leaving hastily from the grassy knoll. Fact or fiction? You be the judge!

[daberti]

People get pretty upset when you make mods to their system -- especially those related to security. I think this just points out a weakness of McAfee's Artemis system. I wonder if there are ways for companies to disable their competition (or software they don't like) by electronically reporting their signatures as "trojans" -- and causing McAfee to remove their executables?

Something to think about, eh?

Quite my thought ;)
Anyway the workaround is at hand. Just what I said above.
Might be an idea to make it sticky -maybe- ;)

[Category 5]

I know viruc checkers seek out keygens and cracks and delete them as though they are viruses. Is it possible some organization has flagged your software as a threat to intellectual property and McAfee is playing ball and targeting your software.

I'm not a consipracy guy, but like I said...keygens get tagged so why not.

[Sophocles]

I find this virus discussion interesting because I received a report on another forum that Avira flagged BD RB for a virus or to quote. the latest version appears to have a TR/Crypt.XPACK.Gen - Trojan! in the file!

I immediately scanned my BD RB folder and nothing came up so I discounted the issue as a pre-existing problem. I do however find it odd that a similar discussion popped up on two separate forums with apparent connection.

So now proceed with your conspiracy theories. LOL:D

[Furiousflea]

I find this virus discussion interesting because I received a report on another forum that Avira flagged BD RB for a virus or to quote.

I immediately scanned my BD RB folder and nothing came up so I discounted the issue as a pre-existing problem. I do however find it odd that a similar discussion popped up on two separate forums with apparent connection.

So now proceed with your conspiracy theories. LOL:D

Not at all, there are commercial packers that lots of developers use to compress\hide their code from being reverse engineerd. These packers are often detcted by AV programs as being dodgy.

No conspiracy theory.


Anyways, jdobbs does the latest version have the freezing resolved for a lot of PiP discs if you don't mind me asking?

Thanks, (soz for still having not mentioned about IG field in bdedit) It will happen.

[setarip_old]

@jdobbs

Think red herring...

[jdobbs]

Not at all, there are commercial packers that lots of developers use to compress\hide their code from being reverse engineerd. These packers are often detcted by AV programs as being dodgy.

No conspiracy theory.


Anyways, jdobbs does the latest version have the freezing resolved for a lot of PiP discs if you don't mind me asking?

Thanks, (soz for still having not mentioned about IG field in bdedit) It will happen. I don't think so, but you never know. I am working a fix for a PiP issue I found for the next version, though. It's more likely it may fix it -- still, since I haven't repeated it I really can't say.

[eTiMaGo]

A note on the whole "Encode Failed. Retrying.", I have been seeing this for quite a lot of movies I ripped (Benjamin Button Disc 1, Unborn, Cars, Beowulf, among others), so I did a lot more reading up on this error in here. My test subject is the Benjamin Button disc which is all 1080p VC1 files, none of which would convert. I'm using the Windows Server 2008 R2 RC, BTW (yeay, another can of worms!), which is really just win7 at the core. And doing BD25 conversions.

Anyway, I tried the trick to force VC1 decoding to WMV9 in ffdshow, to no avail. I tried the other registry tricks, nothing. Then just now out of desperation I set the VC1 decoder to "libavcodec", and now it's working! I set it as a single pass job so I don't waste time in case something goes wrong, but, is there a chance I'm just doing this all wrong and will have to resort to pulling out my hair soon?

[By-Tor]

Hi this my first post here so hope someone can help me i'm trying to back up POTC..TCOTBP and POTC..DMC but keep hitting the same problem with films i'm doing full disc backup
and keep getting to a certain point and failing to re-encode....here is a sample of what i get also I've used 3 different systems and get the same result i've carried out about 5 attempts on each machine with the exact same results

- Input BD size: 39.35 GB
- Approximate total content: [03:22:44.610]
- Target BD size: 22.46 GB
[20:56:50] PHASE ONE, Encoding
- [20:56:50] Extracting A/V streams [VID_00002]
- [20:56:51] Reencoding: VID_00002 (1 of 13)
- [20:57:01] Extracting A/V streams [VID_00014]
- [20:57:05] Reencoding: VID_00014 (2 of 13)
- [20:57:56] Extracting A/V streams [VID_00022]
- [20:58:00] Reencoding: VID_00022 (3 of 13)
- [20:59:03] Extracting A/V streams [VID_00019]
- [20:59:11] Reencoding: VID_00019 (4 of 13)
- [21:04:31] Extracting A/V streams [VID_00021]
- [21:04:39] Reencoding: VID_00021 (5 of 13)
- [21:10:41] Extracting A/V streams [VID_00010]
- [21:10:54] Reencoding: VID_00010 (6 of 13)
- [21:18:39] Extracting A/V streams [VID_00012]
- [21:18:53] Reencoding: VID_00012 (7 of 13)
- [21:24:33] Extracting A/V streams [VID_00017]
- [21:24:47] Reencoding: VID_00017 (8 of 13)
- [21:31:19] Extracting A/V streams [VID_00016]
- [21:31:43] Reencoding: VID_00016 (9 of 13)
- [21:45:01] Extracting A/V streams [VID_00013]
- [21:45:44] Reencoding: VID_00013 (10 of 13)
- [21:56:31] Extracting A/V streams [VID_00018]
- [21:57:59] Reencoding: VID_00018 (11 of 13)
- [22:51:41] Extracting A/V streams [VID_00020]
- [22:55:58] Reencoding: VID_00020 (12 of 13)
- [01:43:10] Extracting A/V streams [VID_00001]
- [02:00:55] Reencoding: VID_00001 (13 of 13)
- Analyzing 20.09 - Encode failed. Retrying.
- Encode failed. Retrying.
- Reached retry limit. Aborting.
- [02:04:04] PredictAndEncode() 00011 2810.

hope this is enough info!!!!!!!!

sorry forgot to say 2 machines xp and 1 is vista 32 bit



just carried out another back up.....same result

[Sn8kbordin]

Used BD-RB 0.26.03 to back up Watchmen in movie only, strict AVCHD mode to DVD9 and when fast forwarding faster than 1.5x on PS3 pictures goes black and stays black. Also this happens when stopping the movie and resuming it, when skipping chapters although it works fine to skip to chapter 2 and some other chapter halfway in the movie. You can hear sound but picture stays black.

Encoding again to see if it will be ok when strict AVCHD is not selected in movie-only.

Finally I tried to encode it into 720p but all working files were 1080p, and .avs files had no resize filter in it.

[tplat]

Has anyone been able to do 25gb movie only back-up of Sin City, with high-res audio?

Just tried beta 26.03 on Sin City and it also failed on movie only, tried with do not convert dts to ac3, do not re-encode ac3 and keep hd audio for bd25, also tried with nothing selected for audio options and it still failed on movie only however full back up seems to start will see the results later. By the way on the movie only option it fails to retrieve audio right after starting.

[isoss]

Heey everyone

i have a question i want to make a ful backup from movies with PiP bud first de schreen whent black and nou te menu hangsup what can i do to prefent it en make a good backup from my movies. i want to keep all of de subs and audio tracks i don't even won't reencode AC3 en DTS and i wan't to keep the HD audio.

can some one help me

[Furiousflea]

Heey everyone

i have a question i want to make a ful backup from movies with PiP bud first de schreen whent black and nou te menu hangsup what can i do to prefent it en make a good backup from my movies. i want to keep all of de subs and audio tracks i don't even won't reencode AC3 en DTS and i wan't to keep the HD audio.

can some one help me

Yeah, read the first post and have a look through the options and don't be so lazy.

[Furiousflea]

Yeah, read the first post and have a look through the options and don't be so lazy.

No disrespect intended with that post, it's just I looked through your post history and you have asked similar question time and time again.

I see you have a Panasonic model that needs 24p to be turned OFF on the player or you will just have a blank screen when going to watch the main movie after the menu. This has been covered countless times in this thread? Can't you do a search for "panasonic" in this thread?

Honestly the motivation for problem solving abilities by ones self in this day and age is tragic.

If you really still need help, then give more details. A demand that is common on all message boards throughout "teh internetz"

[jdobbs]

I've posted links to a new release of BD-RB (v0.27.01) in the first post of this thread. Changes for this version:- Added the capability to reencode secondary video
streams. These were previously copied intact, and
as a result used excessive amounts of space, making
the overall encode quality drop.
- Corrected an error related to secondary tracks and
how they are updated in the SPN tables. This fix
should correct some of the problems related to
playback of video with PiP. Some PiP issues remain
and are being researched.
- Fixed an issue in which on some multiangled sources
the angles may not be properly included in the list
of items to be reencoded. This should fix the issue
where one angle appears to work and another is blank.
- Modified encode quality settings so that they now use
the X264 PRESETS. This makes setting more managable
and keeps BD-RB in line with X264 development.
- Corrected an error in which the percent completed
reported during a minimized state could incorrectly
report 100% overall completion when not true.
- Updated the included X264.EXE in the TOOLS folder
to the lastest tested version (r1195).
- Implemented new settings for first pass of two pass
encodes. Should reduce overall encode times.
- Other minor corrections and cosmetic fixes.

[chudm]

thx jdobbs testing it right now with elton john red piano bluray :)

[Furiousflea]

You "da man" dobbs!!!...testing a "freezing" PiP disc now with sceptical hope :) Thanks for the new release.

[worknstiff]

I will try out the newest version tonight and see how it goes. I finshed with the watchmen fiasco after using every trick I could think of. What is in the m2ts file that is so corrupted that even using TMT to reincode it to AVCH and reset the chapter points it still refuses to ff or chapter seek. I have tried Full disk BD25 backup, Movie Only BD25 and BD9 and finally decided that all you could do is move on. If every one else is able to make it work then maybe it is just my ripping or burning and my old BD30 player that is the problem. All the other movies I have copied have let me take the m2ts file and redo the chapter points and create a fully playable disk using the same configuration so I wonder if it is some new form of m2ts that has different frame rates or time counts or something. Oh well. So now my next problem. I am doing the new BSG 4.5 and really wish there was a way to select multiple alternate playlists to encode. I think that would really be a great extra feature to consider adding.

[Sharc]

Ok. I see. I'll add a "FORCE_ENCODE=1" hidden option to the next version.
Did it already make it for v0.27.01?

[jdobbs]

Did it already make it for v0.27.01?Hmmm... it seems I added it to the code, but didn't include a way to set it from the INI. :o Oh, well, looks like it will have to wait one more version.

[Capsbackup]

Thanks for the new update and your continued diligence. :thanks:
I will test my PiP discs, in particular, Beowulf, which had no secondary audio, but movie freezes.
Just curious, I have successfully backed up Batman Begins, which has PiP and DD Plus secondary audio, but the main movie does not have audio sync. I don't beleive it is a BD-RB issue. I was able to manually, thru tsMuxeR, correct the audio sync ( 250ms) for a movie only and full backup without PiP, but am not able to make all the necessary changes, etc.. for a successful full movie backup with PiP.
Is it possible to have an option within BD-RB to change the audio delay for a full backup or movie only backup?
It would be nice, if after a normal rebuild that has audio async, to be able to set a delay and do another rebuild only to try and correct the audio sync.( keeping Working folder files)

[Capsbackup]

Sorry to report, but a full movie backup of Beowulf, BD-25, burned to BD-RE for playback on my BX1 still has the picture freezing. :(
Also, the border surrounding the PiP window is all that is displayed before the picture freezes, never actually showing the PiP video.
I also noticed, which may be part of BD-RBV02701, that the backups are now reported by BDInfo as Baseline Profile 4.1 for the main movie and the secondary PiP track, where the original movie and the previous BD-RBV02603 is seen as High Profile 4.1 and 3.2, respectively. Not sure what, if any, this difference makes, but just my observation.
jdobbs, this PiP backup may be proving to be more trouble than it's worth, but if you are determined to make it work, I will continue to test it out on my end. :)

[dianasta]

Hi jdobbs,

I'm using BD-RB 0.27.01 rebuilding X Files 2. The secondary audio is not selected for some reason.

I have set the parameter PROCESS_SECONDARY=1 in the .ini file.

I have attached the picture for your review.


Thanks.

[jdobbs]

Sorry to report, but a full movie backup of Beowulf, BD-25, burned to BD-RE for playback on my BX1 still has the picture freezing. :(
Also, the border surrounding the PiP window is all that is displayed before the picture freezes, never actually showing the PiP video.
I also noticed, which may be part of BD-RBV02701, that the backups are now reported by BDInfo as Baseline Profile 4.1 for the main movie and the secondary PiP track, where the original movie and the previous BD-RBV02603 is seen as High Profile 4.1 and 3.2, respectively. Not sure what, if any, this difference makes, but just my observation.
jdobbs, this PiP backup may be proving to be more trouble than it's worth, but if you are determined to make it work, I will continue to test it out on my end. :)Baseline? I'll look at it -- but that sounds weird... what quality setting are you using? I used the "ultrafast" preset for the "High Speed (BD-25)" option. If you used that one it probably isn't surprising that it's baseline -- as it would make sense that it would be faster without processing b-frames. It shouldn't make a difference for BD playback, though.

[Capsbackup]

Baseline? I'll look at it -- but that sounds weird... what quality setting are you using? I used the "ultrafast" preset for the "High Speed (BD-25)" option. If you used that one it probably isn't surprising that it's baseline -- as it would make sense that it would be faster without processing b-frames. It shouldn't make a difference for BD playback, though.

I used High Speed Option, One Pass Encoding, Quicker Encode for Extras.

[jdobbs]

I also noticed, which may be part of BD-RBV02701, that the backups are now reported by BDInfo as Baseline Profile 4.1 for the main movie and the secondary PiP track, where the original movie and the previous BD-RBV02603 is seen as High Profile 4.1 and 3.2, respectively. Not sure what, if any, this difference makes, but just my observation.The "ultrafast" mode definitely sets bframes to "0" -- that's why it shows as baseline. I thought about adding "--bframes 3" to the command line to make it more consistent, but the real purpose of that setting is speed -- and in testing it this morning I found that it is 40% faster without the bframes.

If I start getting reports that the quality isn't good enough even on BD-25, I'll put the bframes back in.

[jdobbs]

Hi jdobbs,

I'm using BD-RB 0.27.01 rebuilding X Files 2. The secondary audio is not selected for some reason.

I have set the parameter PROCESS_SECONDARY=1 in the .ini file.

I have attached the picture for your review.


Thanks. That's because it is a DTS secondary, which TSMUXER can't be extract right now.

[Fullasoul]

hey, guys....

So I ran into an "error in attempt to multiplex" error last night....searching this thread thoroughly before posting, I see that this particular question very rarely gets answered, but I DID see that the next logical step is to try and perform the function from the command line, so I did. Here's what came up:

Decoding H264 stream (track 1): Profile: High@4.1 Resolution: 1920:1080p Frame
rate: 23.976
H.264 stream does not contain fps field. Muxing fps=23.976
0.0% complete
H264 bitstream changed: insert nal unit delimiters
H264 bitstream changed: insert pict timing and buffering period SEI units
Decoding AC3 stream (track 2): Bitrate: 640Kbps Sample Rate: 48KHz Channels: 6
Decoding AC3 stream (track 3): Bitrate: 192Kbps Sample Rate: 48KHz Channels: 2
Decoding PGS stream (track 4): Resolution: 1920:1080 Frame rate: 23.976
H264 bitstream changed: insert SPS/PPS units
18.2% complete
Matroska parser: read error at pos 1063256064

Any idea what's going wrong???

[Capsbackup]

The "ultrafast" mode definitely sets bframes to "0" -- that's why it shows as baseline. I thought about adding "--bframes 3" to the command line to make it more consistent, but the real purpose of that setting is speed -- and in testing it this morning I found that it is 40% faster without the bframes.

If I start getting reports that the quality isn't good enough even on BD-25, I'll put the bframes back in.

I was not able to check the quality because the disc would freeze, but I did like the speed of this setting. I'm sure the quality would still be excellent for most full movie backups to BD-25 without a lot of extras. I'm all for a quick backup setting like this one. If I am after maximum quality, I know I can select that option too.

[By-Tor]

hello again sorry to keep asking, but i need some help .......i posted 2 days ago trying to find out if anyone else had any problems backing up
the pirates of the caribbean 1+2, I've been trying for over 2 months using various beta version's of bd-rebuilder but keep getting the same problem
in that i'm trying to do a full disc backup but it keeps failing giving me these reults.
- Input BD size: 39.35 GB
- Approximate total content: [03:22:44.610]
- Target BD size: 22.46 GB
[20:56:50] PHASE ONE, Encoding
- [20:56:50] Extracting A/V streams [VID_00002]
- [20:56:51] Reencoding: VID_00002 (1 of 13)
- [20:57:01] Extracting A/V streams [VID_00014]
- [20:57:05] Reencoding: VID_00014 (2 of 13)
- [20:57:56] Extracting A/V streams [VID_00022]
- [20:58:00] Reencoding: VID_00022 (3 of 13)
- [20:59:03] Extracting A/V streams [VID_00019]
- [20:59:11] Reencoding: VID_00019 (4 of 13)
- [21:04:31] Extracting A/V streams [VID_00021]
- [21:04:39] Reencoding: VID_00021 (5 of 13)
- [21:10:41] Extracting A/V streams [VID_00010]
- [21:10:54] Reencoding: VID_00010 (6 of 13)
- [21:18:39] Extracting A/V streams [VID_00012]
- [21:18:53] Reencoding: VID_00012 (7 of 13)
- [21:24:33] Extracting A/V streams [VID_00017]
- [21:24:47] Reencoding: VID_00017 (8 of 13)
- [21:31:19] Extracting A/V streams [VID_00016]
- [21:31:43] Reencoding: VID_00016 (9 of 13)
- [21:45:01] Extracting A/V streams [VID_00013]
- [21:45:44] Reencoding: VID_00013 (10 of 13)
- [21:56:31] Extracting A/V streams [VID_00018]
- [21:57:59] Reencoding: VID_00018 (11 of 13)
- [22:51:41] Extracting A/V streams [VID_00020]
- [22:55:58] Reencoding: VID_00020 (12 of 13)
- [01:43:10] Extracting A/V streams [VID_00001]
- [02:00:55] Reencoding: VID_00001 (13 of 13)
- Analyzing 20.09 - Encode failed. Retrying.
- Encode failed. Retrying.
- Reached retry limit. Aborting.
- [02:04:04] PredictAndEncode() 00011 2810.
-pass1/1
speed0.52x
eta 0:00
fps:12.46
frames 042710/042717
this was using version 27.01 today

hope this is enough info!!!



hope someone can guide with this one....
p/s borrowed another copy of the disc from a friend to make sure it's not my disc
still got the same result...HELP!!!!!!!!! Please.

--------------------------------------------------------------------------

[Capsbackup]

@By-Tor;
What region is your POTC disc?
Have you been succsessful backing up any other discs?
Can you do a movie only backup successfully of this POTC disc?

[By-Tor]

hi disc's tried have been region B and i've managed to backup potc 3 no problems also various other BD's
only having trouble with potc curse of the black pearl and potc dead mans chest????????

[drmih]

hello again sorry to keep asking, but i need some help .......i posted 2 days ago trying to find out if anyone else had any problems backing up
the pirates of the caribbean 1+2, I've been trying for over 2 months using various beta version's of bd-rebuilder but keep getting the same problem
in that i'm trying to do a full disc backup but it keeps failing giving me these reults.
- Input BD size: 39.35 GB
- Approximate total content: [03:22:44.610]
- Target BD size: 22.46 GB
[20:56:50] PHASE ONE, Encoding
- [20:56:50] Extracting A/V streams [VID_00002]
- [20:56:51] Reencoding: VID_00002 (1 of 13)
- [20:57:01] Extracting A/V streams [VID_00014]
- [20:57:05] Reencoding: VID_00014 (2 of 13)
- [20:57:56] Extracting A/V streams [VID_00022]
- [20:58:00] Reencoding: VID_00022 (3 of 13)
- [20:59:03] Extracting A/V streams [VID_00019]
- [20:59:11] Reencoding: VID_00019 (4 of 13)
- [21:04:31] Extracting A/V streams [VID_00021]
- [21:04:39] Reencoding: VID_00021 (5 of 13)
- [21:10:41] Extracting A/V streams [VID_00010]
- [21:10:54] Reencoding: VID_00010 (6 of 13)
- [21:18:39] Extracting A/V streams [VID_00012]
- [21:18:53] Reencoding: VID_00012 (7 of 13)
- [21:24:33] Extracting A/V streams [VID_00017]
- [21:24:47] Reencoding: VID_00017 (8 of 13)
- [21:31:19] Extracting A/V streams [VID_00016]
- [21:31:43] Reencoding: VID_00016 (9 of 13)
- [21:45:01] Extracting A/V streams [VID_00013]
- [21:45:44] Reencoding: VID_00013 (10 of 13)
- [21:56:31] Extracting A/V streams [VID_00018]
- [21:57:59] Reencoding: VID_00018 (11 of 13)
- [22:51:41] Extracting A/V streams [VID_00020]
- [22:55:58] Reencoding: VID_00020 (12 of 13)
- [01:43:10] Extracting A/V streams [VID_00001]
- [02:00:55] Reencoding: VID_00001 (13 of 13)
- Analyzing 20.09 - Encode failed. Retrying.
- Encode failed. Retrying.
- Reached retry limit. Aborting.
- [02:04:04] PredictAndEncode() 00011 2810.
-pass1/1
speed0.52x
eta 0:00
fps:12.46
frames 042710/042717
this was using version 27.01 today

hope this is enough info!!!



hope someone can guide with this one....
p/s borrowed another copy of the disc from a friend to make sure it's not my disc
still got the same result...HELP!!!!!!!!! Please.

--------------------------------------------------------------------------

I've done all 6 discs Region B without a problem but my file structures looks different - also why are the files in a random order - it usually starts at the lowest id and works through. Perhaps there are one disc editions that you are doing and there's something quirky about them.

[dianasta]

That's because it is a DTS secondary, which TSMUXER can't be extract right now.

Is it possible to have an option to encode that type of audio in future releases?

Thanks.

[drmih]

Is it possible to have an option to encode that type of audio in future releases?

Thanks.

You'd have to ask that question of the team behind TSmuxer.

[DK]

trying to find out if anyone else had any problems backing up the pirates of the caribbean 1+2

No problem here with either of the three titles:

[14:41:59] BD Rebuilder v0.25.04 (beta)
- Input BD size: 41,31 GB
- Approximate total content: [03:21:15.179]
- Target BD size: 22,46 GB
- SHUTDOWN at completion enabled
[14:41:59] PHASE ONE, Encoding
- [14:41:59] Extracting A/V streams [VID_00002]
- [14:41:59] Reencoding: VID_00002 (1 of 10)
- [14:42:03] Extracting A/V streams [VID_00003]
- [14:42:04] Reencoding: VID_00003 (2 of 10)
- [14:42:21] Extracting A/V streams [VID_00017]
- [14:42:23] Reencoding: VID_00017 (3 of 10)
- [14:42:36] Extracting A/V streams [VID_00022]
- [14:43:09] Reencoding: VID_00022 (4 of 10)
- [14:44:09] Extracting A/V streams [VID_00023]
- [14:44:44] Reencoding: VID_00023 (5 of 10)
- [14:45:44] Extracting A/V streams [VID_00014]
- [14:46:35] Reencoding: VID_00014 (6 of 10)
- [14:48:14] Extracting A/V streams [VID_00031]
- [14:49:11] Reencoding: VID_00031 (7 of 10)
- [14:51:09] Extracting A/V streams [VID_00032]
- [14:51:21] Reencoding: VID_00032 (8 of 10)
- [14:55:10] Extracting A/V streams [VID_00021]
- [14:57:32] Reencoding: VID_00021 (9 of 10)
- [16:43:58] Extracting A/V streams [VID_00001]
- [16:51:27] Reencoding: VID_00001 (10 of 10)
[20:41:45]PHASE ONE complete
[20:41:45]PHASE TWO - Rebuild Started
- [20:41:45] Rebuilding BD file Structure
[20:42:52] - Encode and Rebuild complete


[00:02:53] BD Rebuilder v0.25.04 (beta)
- Input BD size: 39,35 GB
- Approximate total content: [03:22:44.610]
- Target BD size: 22,46 GB
[00:02:54] PHASE ONE, Encoding
- [00:02:54] Extracting A/V streams [VID_00002]
- [00:02:54] Reencoding: VID_00002 (1 of 13)
- [00:02:58] Extracting A/V streams [VID_00014]
- [00:02:59] Reencoding: VID_00014 (2 of 13)
- [00:03:21] Extracting A/V streams [VID_00022]
- [00:03:23] Reencoding: VID_00022 (3 of 13)
- [00:03:50] Extracting A/V streams [VID_00019]
- [00:03:53] Reencoding: VID_00019 (4 of 13)
- [00:05:47] Extracting A/V streams [VID_00021]
- [00:05:51] Reencoding: VID_00021 (5 of 13)
- [00:07:53] Extracting A/V streams [VID_00010]
- [00:07:56] Reencoding: VID_00010 (6 of 13)
- [00:10:46] Extracting A/V streams [VID_00012]
- [00:10:50] Reencoding: VID_00012 (7 of 13)
- [00:12:46] Extracting A/V streams [VID_00017]
- [00:12:51] Reencoding: VID_00017 (8 of 13)
- [00:15:21] Extracting A/V streams [VID_00016]
- [00:15:28] Reencoding: VID_00016 (9 of 13)
- [00:20:10] Extracting A/V streams [VID_00013]
- [00:20:23] Reencoding: VID_00013 (10 of 13)
- [00:24:27] Extracting A/V streams [VID_00018]
- [00:24:54] Reencoding: VID_00018 (11 of 13)
- [00:43:36] Extracting A/V streams [VID_00020]
- [00:44:52] Reencoding: VID_00020 (12 of 13)
- [01:42:06] Extracting A/V streams [VID_00001]
- [01:49:47] Reencoding: VID_00001 (13 of 13)
[05:52:22]PHASE ONE complete
[05:52:22]PHASE TWO - Rebuild Started
- [05:52:23] Rebuilding BD file Structure
[05:52:56] - Encode and Rebuild complete


[15:14:56] BD Rebuilder v0.25.04 (beta)
- Input BD size: 42,93 GB
- Approximate total content: [03:00:04.335]
- Target BD size: 22,46 GB
- SHUTDOWN at completion enabled
[15:14:56] PHASE ONE, Encoding
- [15:14:56] Extracting A/V streams [VID_00002]
- [15:14:57] Reencoding: VID_00002 (1 of 10)
- [15:15:00] Extracting A/V streams [VID_00005]
- [15:15:01] Reencoding: VID_00005 (2 of 10)
- [15:15:14] Extracting A/V streams [VID_00007]
- [15:15:15] Reencoding: VID_00007 (3 of 10)
- [15:15:28] Extracting A/V streams [VID_00012]
- [15:15:29] Reencoding: VID_00012 (4 of 10)
- [15:16:00] Extracting A/V streams [VID_00023]
- [15:16:03] Reencoding: VID_00023 (5 of 10)
- [15:16:56] Extracting A/V streams [VID_00004]
- [15:17:00] Reencoding: VID_00004 (6 of 10)
- [15:18:32] Extracting A/V streams [VID_00006]
- [15:18:40] Reencoding: VID_00006 (7 of 10)
- [15:21:33] Extracting A/V streams [VID_00008]
- [15:21:42] Reencoding: VID_00008 (8 of 10)
- [15:25:48] Extracting A/V streams [VID_00003]
- [15:26:06] Reencoding: VID_00003 (9 of 10)
- [15:35:41] Extracting A/V streams [VID_00001]
- [15:49:48] Reencoding: VID_00001 (10 of 10)
[20:56:30]PHASE ONE complete
[20:56:30]PHASE TWO - Rebuild Started
- [20:56:30] Rebuilding BD file Structure
[20:56:52] - Encode and Rebuild complete

[drmih]

Just checked Madagscar 2 with had PiP and DD+. Done it to both bd-25 and bd-9. In both case the audio is warbley and whatever you do the audio it plays with the movie is 192kbps, which is the DD+ track. According to TSmuxer the others are there. The PiP does work and you can just about figure out that the part of the audio is in sync with the PiP window.

As an aside, the bd-9, when played on a Sony 550 still gives no audio at all, or access to the PiP.