RipBot264 v1.18.3 - Simple and easy to use GUI -> IPOD . PSP . CONSOLES . BLURAY

[GZZ]

Must be a bug, as I see the input framerate from avs2yuv (10000000/417083) but I dont think x264 sees this and output a default 25 fps stream, which is wrong.

[Atak_Snajpera]

This is not serious bug because it will be corrected after muxing to container. I will fix this next time.

[GZZ]

is the solution to set the --FPS 10000000/417083 or will --FPS 24000/1001 be correct or dosnt it matter which one I use ?

[Atak_Snajpera]

even 23.976 should be ok

[mmmmdonut]

I've got a question about the codec id field. On my files I create (I use apple tv preset) some show isom while most show M4VH. Can someone explain why there is a difference? I'm not having any issues playing either with my apple tv, but just curious whythere are differences.

Thx

[Atak_Snajpera]

what are you talking about?

[cmx]

hi All
i have question
when i encode .mpg about 7 gb (caputed from HD camera) to .mkv (2 pass ,lock size 4480)
in version 1.13.1 i'm getting final size 5472
all my blue-rays works ok i'm getting 4480 size
any one alse experiencing some problem?
thx
dzieki !

[Atak_Snajpera]

show me log

[cmx]

show me log

thanks!

[dchao]

Atak,

Why did you turn off the VC-1 codec on the ffdshow video config page?

I installed ffdshow (rev2672) check the video config page, and the VC-1 was enabled using libavcodec.

Ran RipBot264 (1.13.1) and added HD-DVD video, I got a no compressor found message. Checked the video config page and VC-1 was set to "disabled".

[8ternity]

@Atak:

Hey Atak_Snajpera, did you see the MT application for AVIsynth ?

http://avisynth.org/mediawiki/MT

http://avisynth.org/mediawiki/MT_support_page

Did you think if it can be installed in ripbot264 in future?
Question: did an AMD 64 X2 is Multi Thread ??

Thanks!!

[xaero]

1. No
2. No

oh well.. :cool:

[mmmmdonut]

what are you talking about?

lol. Sorry about that. Should have clarified a little better. Anyway looking at mediainfo on a few of my encodes, I notice some (primarily animation titles) have a codec id of isom and on the majority of other flicks the codec id is M4VH.


Format : MPEG-4
Format profile : Base Media
Codec ID : isom

Format : MPEG-4
Format profile : Apple TV
Codec ID : M4VH

All my files are created using Apple TV profile and resized to play back on that device. Like I mentioned before I'm not having any issues just trying to understand where this is coming from.

Cheers

[~bT~]

ok, this new version no longer remembers my setting for audio, resize, audio boost etc.
older version remembered most settings after adding the 1st vid and was handy for when i encoded vidz for ipod.
now i have to set it up all again for every new vid i add..

[Atak_Snajpera]

I installed ffdshow (rev2672) check the video config page, and the VC-1 was enabled using libavcodec.

wmv9 is better decoder for VC-1 than libavcodec. libavcodec does not support interlaced video (for example recorded gig) and is a little less stable than microsoft's decoder. You better install WMV11.

[Atak_Snajpera]

ok, this new version no longer remembers my setting for audio, resize, audio boost etc.
older version remembered most settings after adding the 1st vid and was handy for when i encoded vidz for ipod.
now i have to set it up all again for every new vid i add..
What did you that resize is not remebered?

[~bT~]

^ in v1.12.0 for conversion to ipod format

i load any file, set audio to 96kbps, set normalize to 200%, set cq22, hit properties and set resize to POD. then hit OK and OK to save.

next i load any file again, once all the scanning, demuxing etc is done, i dont need to set any options as they were remembered from previos save.

in v1.13.1

i have to set all options again on every new file loaded after the 1st one.

[Atak_Snajpera]

Ok. I confirm. Audio profile and normalize are not remebered as well as iPod resize profile.

[~bT~]

^ yes atak.

[~bT~]

wmv9 is better decoder for VC-1 than libavcodec. libavcodec does not support interlaced video (for example recorded gig) and is a little less stable than microsoft's decoder. You better install WMV11.

is libav for avc better than divx7?

[Atak_Snajpera]

Unfortunately Divx7 does not detect fps when DirectShowSource is used in script. libav has no problems.

[cmx]

hi Atak
did you had a chance to look at my log file :)
thanks

[Atak_Snajpera]

Tell me how was I suppose to check your log?????

[cmx]

Tell me how was I suppose to check your log?????

sorry on page 203
Attachments Pending Approval
thanks

[whats85]

I just installed Nero 8 with Showtime because my dvd's didnt play audio anymore. Now that problem is fixed but will this have an effect on RipBot?

[juGGaKNot]

Yes, also "unknown option -- nal-hrd", you have my log on a page.

Also, if i add 2 jobs the first one fails, if i add it on its own it works.

upgrading to 1.13.1 on sunday.

[Ajax_Undone]

sorry on page 203
Attachments Pending Approval
thanks

Use the Code Tags and copy and paste... Your log content

[thehuey]

wmv9 is better decoder for VC-1 than libavcodec. libavcodec does not support interlaced video (for example recorded gig) and is a little less stable than microsoft's decoder. You better install WMV11.

Everytime I install WMP9 and WME9 it causes RipBot to stop working correctly.

After installing those 2 apps, whenever RipBot is done demuxing the audio it tries to open the avs in MPC and spits out a ACM :: Output Wrapper error, or something like that.

So I steer clear of installing those applications. I've tested many times and the only time Ripbot gives me those errors is right after installing those apps.

[Atak_Snajpera]

I meant WMP11 http://www.microsoft.com/windows/windowsmedia/player/11/default.aspx

[cmx]

when i encode .mpg about 16 gb (caputed from HD camera) to .mkv (2 pass ,lock size 4480)
in version 1.13.1 i'm getting final size 5472
all my blue-rays works ok i'm getting 4480 size
thx
dzieki !

Hereis my log file


F:\>"C:\Users\Artur\Downloads\hddvd\RipBot264v1.13.1\tools\avs2yuv\pipebuf.exe" "C:\Users\Artur\Downloads\hddvd\RipBot264v1.13.1\tools\avs2yuv\avs2yuv.exe" "F:\temp\RipBot264temp\job1\job1.avs" -raw - : "C:\Users\Artur\Downloads\hddvd\RipBot264v1.13.1\tools\x264\x264_x64.exe" --pass 1 --bitrate 6942 --stats "F:\temp\RipBot264temp\job1\job1.stats" --sar 1333:1000 --level 4.0 --vbv-bufsize 25000 --vbv-maxrate 25000 --filter 0,0 --ref 3 --mixed-refs --bframes 3 --b-adapt 1 --weightb --direct auto --subme 7 --trellis 1 --partitions all --8x8dct --me umh --threads auto --thread-input --progress --no-psnr --no-ssim --frames 153556 --partitions none --subme 3 --me dia --output "F:\temp\RipBot264temp\video.264" - 1440x1080 : 4

x264 [info]: using SAR=1333/1000
x264 [info]: using cpu capabilities: MMX2 SSE2Fast SSSE3 PHADD SSE4.1 Cache64
x264 [info]: profile High, level 4.0
F:\temp\RipBot264temp\job1\job1.avs: 1440x1080, 30000/1001 fps, 153556 frames

x264 [info]: slice I:817 Avg QP:21.59 size:109904
x264 [info]: slice P:81553 Avg QP:23.69 size: 48745
x264 [info]: slice B:71186 Avg QP:25.39 size: 17865
x264 [info]: consecutive B-frames: 15.1% 61.5% 20.4% 3.0%
x264 [info]: mb I I16..4: 8.9% 65.9% 25.2%
x264 [info]: mb P I16..4: 24.5% 0.0% 0.0% P16..4: 70.0% 0.0% 0.0% 0.0% 0.0% skip: 5.5%
x264 [info]: mb B I16..4: 4.4% 0.0% 0.0% B16..8: 27.2% 0.0% 0.0% direct:25.6% skip:42.7% L0:43.4% L1:38.0% BI:18.7%
x264 [info]: final ratefactor: 23.16
x264 [info]: 8x8 transform intra:2.2% inter:60.4%
x264 [info]: direct mvs spatial:100.0% temporal:0.0%
x264 [info]: ref P L0 67.6% 19.3% 13.1%
x264 [info]: ref B L0 73.9% 26.1%
x264 [info]: kb/s:6951.0

encoded 153556 frames, 29.14 fps, 6951.04 kb/s

F:\>"C:\Users\Artur\Downloads\hddvd\RipBot264v1.13.1\tools\avs2yuv\pipebuf.exe" "C:\Users\Artur\Downloads\hddvd\RipBot264v1.13.1\tools\avs2yuv\avs2yuv.exe" "F:\temp\RipBot264temp\job1\job1.avs" -raw - : "C:\Users\Artur\Downloads\hddvd\RipBot264v1.13.1\tools\x264\x264_x64.exe" --pass 2 --bitrate 6942 --stats "F:\temp\RipBot264temp\job1\job1.stats" --sar 1333:1000 --level 4.0 --vbv-bufsize 25000 --vbv-maxrate 25000 --filter 0,0 --ref 3 --mixed-refs --bframes 3 --b-adapt 1 --weightb --direct auto --subme 7 --trellis 1 --partitions all --8x8dct --me umh --threads auto --thread-input --progress --no-psnr --no-ssim --frames 153556 --output "F:\temp\RipBot264temp\video.264" - 1440x1080 : 4

x264 [info]: using SAR=1333/1000
x264 [info]: using cpu capabilities: MMX2 SSE2Fast SSSE3 PHADD SSE4.1 Cache64
x264 [info]: profile High, level 4.0
F:\temp\RipBot264temp\job1\job1.avs: 1440x1080, 30000/1001 fps, 153556 frames


x264 [info]: slice I:817 Avg QP:21.97 size:111068
x264 [info]: slice P:81553 Avg QP:24.36 size: 48753
x264 [info]: slice B:71186 Avg QP:25.95 size: 17743
x264 [info]: consecutive B-frames: 15.1% 61.5% 20.4% 3.0%
x264 [info]: mb I I16..4: 3.4% 86.3% 10.2%
x264 [info]: mb P I16..4: 0.4% 10.1% 0.3% P16..4: 56.7% 14.9% 12.1% 0.1% 0.2% skip: 5.3%
x264 [info]: mb B I16..4: 0.0% 0.7% 0.0% B16..8: 53.3% 0.6% 1.2% direct: 4.9% skip:39.3% L0:42.0% L1:52.6% BI: 5.4%
x264 [info]: 8x8 transform intra:92.7% inter:82.0%
x264 [info]: direct mvs spatial:99.6% temporal:0.4%
x264 [info]: ref P L0 69.4% 18.7% 12.0%
x264 [info]: ref B L0 79.5% 20.5%
x264 [info]: kb/s:6941.7

encoded 153556 frames, 11.52 fps, 6941.76 kb/s

F:\>"C:\Users\Artur\Downloads\hddvd\RipBot264v1.13.1\tools\mkvtoolnix\mkvmerge.exe" -o "Q:\hddvd capture\tape3\fix bitrate.mkv" --default-duration 0:29.97fps -d 0 -A -S "F:\temp\RipBot264temp\video.264" --language 0:und --sync 0:-136 -a 0 -D -S "F:\temp\RipBot264temp\job1\job1 Tc0 L2 2ch 48 384 DELAY -136ms.mp2"
mkvmerge v2.4.0 ('Fumbling Towards Ecstasy') built on Oct 11 2008 20:10:57
'F:\temp\RipBot264temp\video.264': Using the AVC/h.264 ES demultiplexer.
'F:\temp\RipBot264temp\job1\job1 Tc0 L2 2ch 48 384 DELAY -136ms.mp2': Using the MP2/MP3 demultiplexer.
'F:\temp\RipBot264temp\video.264' track 0: Extracted the aspect ratio information from the MPEG-4 layer 10 (AVC) video data and set the display dimensions to 1920/1080.
'F:\temp\RipBot264temp\video.264' track 0: Using the MPEG-4 part 10 ES video output module.
'F:\temp\RipBot264temp\job1\job1 Tc0 L2 2ch 48 384 DELAY -136ms.mp2' track 0: Using the MPEG audio output module.
The file 'Q:\hddvd capture\tape3\fix bitrate.mkv' has been opened for writing.
Warning: 'F:\temp\RipBot264temp\job1\job1 Tc0 L2 2ch 48 384 DELAY -136ms.mp2' track 0: This MPEG audio track contains 722 bytes of non-MP3 data which were skipped. The audio/video synchronization may have been lost.
Warning: 'F:\temp\RipBot264temp\job1\job1 Tc0 L2 2ch 48 384 DELAY -136ms.mp2' track 0: This MPEG audio track contains 1090 bytes of non-MP3 data which were skipped. The audio/video synchronization may have been lost.
Warning: 'F:\temp\RipBot264temp\job1\job1 Tc0 L2 2ch 48 384 DELAY -136ms.mp2' track 0: This MPEG audio track contains 354 bytes of non-MP3 data which were skipped. The audio/video synchronization may have been lost.

The cue entries (the index) are being written...

Muxing took 80 seconds.
-------------------------

Elapsed Time: 05h:12m:00s

[dchao]

wmv9 is better decoder for VC-1 than libavcodec. libavcodec does not support interlaced video (for example recorded gig) and is a little less stable than microsoft's decoder. You better install WMV11.

I opened ffdshow video config again, wmv9 is listed under VC-1, so I changed it from libavcodec to wmv9. What puzzled me was why RipBot264 made the change for me? And then when I ran RipBot264 again , this setting would stick, and everything was fine after that.

BTW, I have WMP11 installed, running XP-SP3.

[Atak_Snajpera]

WMP11 decoder is used in two cases:
1) user selects disabled
2) user selects wmv9

Here what I did:
1) if app detects that libavcodec is enabled then disabled is selected
2) if app detects that wmv9 is enabled then it does not change anything

[illestdomer2005]

Has anyone had any trouble converting Vicky Cristina Barcelona? I did Lakeview Terrace and Barcelona in the same queue, and I wound up with the audio from Lakeview Terrace on the Barcelona conversion...

What was weird, though, was that when I was setting up Barcelona, I got an error message when I tried to preview the job. It said something about not being able to render certain pins in the graph re: ACM Wrapper::output or something.

Just curious as to what this would be.

[Atak_Snajpera]

give me more info about video and audio

[dchao]

Here what I did:
1) if app detects that libavcodec is enabled then disabled is selected
2) if app detects that wmv9 is enabled then it does not change anything

I think this is very confusing for users. Because the default VC-1 setting in ffdshow is libavcodec, even when WMP11/10 is installed and wmv9 is listed as an option. So the first time an user loads a VC-1 video, and the first message hit the user is "no compressor found" with no explanation what so ever.

Can you change the behavior of the app in step (1). So it works like this:

1) if app detects libavcodec is enabled then check if wmv9 is installed, if so change this setting to wmv9, otherwise disable VC-1.

[Wishbringer]

@Atak_Snajpera:

I can change ini that it uses 2-pass instead of CQ and can set bitrate and bluray struct as output...
But can I set encode for fixed size (DVD9 8150MB) in ini per default?

[okivanleer]

Hello.

I was wondering if anyone else was having the same problem that I am. Using 1.13.0 or 1.13.1 my output speed for a 23.976 movie is changed to 25 during the conversion. This happens even if I assume > 23.975. The weird thing is that the mkv is perfectly synced, but when i run through tsmuxer the audio is seconds off. I've tried multiple movies and the outcome is the same. I've rolled back to 1.12.0 and everything works. Any ideas?

[wakebrder]

Has anyone had any trouble converting Vicky Cristina Barcelona? I did Lakeview Terrace and Barcelona in the same queue, and I wound up with the audio from Lakeview Terrace on the Barcelona conversion...

What was weird, though, was that when I was setting up Barcelona, I got an error message when I tried to preview the job. It said something about not being able to render certain pins in the graph re: ACM Wrapper::output or something.

Just curious as to what this would be.

Vicky Christina Barcelona has a 2 channel PCM audio as the only audio track. Ripbot converts this to Flac, but I cannot get the audio to sync.

[Atak_Snajpera]

I think this is very confusing for users. Because the default VC-1 setting in ffdshow is libavcodec, even when WMP11/10 is installed and wmv9 is listed as an option. So the first time an user loads a VC-1 video, and the first message hit the user is "no compressor found" with no explanation what so ever.
By default VC-1 and WMV1/2/3 are disabled in ffdshow. Remove ffdshow and all registry settings and see yourself if you don't believe me.


Hello.

I was wondering if anyone else was having the same problem that I am. Using 1.13.0 or 1.13.1 my output speed for a 23.976 movie is changed to 25 during the conversion. This happens even if I assume > 23.975. The weird thing is that the mkv is perfectly synced, but when i run through tsmuxer the audio is seconds off. I've tried multiple movies and the outcome is the same. I've rolled back to 1.12.0 and everything works. Any ideas?

http://forum.doom9.org/showthread.php?p=1248210#post1248210
http://forum.doom9.org/showthread.php?p=1248239#post1248239

[8ternity]

Hi Atak,

Still have the same trouble when convert an MKV 1080P to Blu-Ray 1080P but 23.97FPS audio is not syncronized.

Softwares: Ripbot 1.13.1, ffdshow 2633MT, Avisynth 2.5.8, matroska latest.

Can you help me with that please??

Note: I try convert 23,97FPS and 24 FPS and audio still desync.

Here the desync time snapshot to 23.97FPS;

http://i480.photobucket.com/albums/rr165/8ternity/Other/th_2009-02-13-Snapshot02.jpg (http://s480.photobucket.com/albums/rr165/8ternity/Other/?action=view&current=2009-02-13-Snapshot02.jpg)

After conversion done, audio out of sync.


#MT


#VideoSource

video=DirectShowSource("D:\--= Complete =--\LE RETOUR DU ROI.mkv",audio=false).ConvertToYV12()

#Deinterlace



#Decimate



#Crop



#Resize
video=Spline36Resize(video,1920,800).Sharpen(0.2).AddBorders(0,140,0,140)


#Colors



#Denoise
LoadPlugin("C:\Program Files (x86)\Ripbot264\Tools\AviSynth plugins\fft3dgpu\fft3dgpu.dll")
LoadPlugin("C:\Program Files (x86)\Ripbot264\Tools\AviSynth plugins\gradfun2db\gradfun2db.dll")
video=FFT3DGPU(video,sigma=1.25).gradfun2db

#Subtitles



#AudioSource
LoadPlugin("C:\Program Files (x86)\Ripbot264\tools\AviSynth plugins\NicAudio\NicAudio.dll")
audio=NicAC3Source("D:\temp\RipBot264temp\job1\audio.1.ac3")
audio=ResampleAudio(audio,48000)
#DownMix
Import("C:\Program Files (x86)\Ripbot264\Tools\AviSynth plugins\Scripts\DownMixAudio.avs")
audio=DownMix2Stereo(audio)

#Delay
audio=DelayAudio(audio,0)


#Tempo
video=AssumeFPS(video,23.976)
audio=TimeStretch(audio,tempo=23.976/25*100)

#Normalize



#AudioDub
audio=ConvertAudioTo16bit(audio)
AudioDub(video,audio)

#Triming



#ColorSpace
ConvertToRGB


7 minutes of difference. I start the project yesturday and let this like that, but play the project done and audio not correct like in the past version.

8iternity

[hoju3508]

Thanks for the sup support.

[illestdomer2005]

Vicky Christina Barcelona has a 2 channel PCM audio as the only audio track. Ripbot converts this to Flac, but I cannot get the audio to sync.

It's actually a 3 channel audio track that for some reason limits RipBot to 2 channels...? But yeah, I got the FLAC file that was apparently never used and did not contain the dialogue channel...at least not mixed properly for my 2 channel headphone out.

I also demuxed it to a wav file and tried to tell RipBot to use it as the audio track, but no luck. It still grabbed the Lakeview Terrace audio that was in a previous job.

[illestdomer2005]

give me more info about video and audio

What do you want to know? The video is VC-1 1080p 24fps, and the audio is a 3 channel LPCM soundtrack. Do you want the media info stats from the .m2ts file?

[Blackwalker]

hi Atak, first of thx for your hard work.
are you going to release a new version?
thx!

[Atak_Snajpera]

and the audio is a 3 channel LPCM soundtrack.
send me 50 mb flac or pcm sample

[Nemesis7]

Hi Atak_Snajpera, glad to see you added soft subs to Ripbot264. Is there a possibility you can make (multiple) srt subs work on the iPhone?

Btw, can you make it possible to change the frequency of audio in the main menu instead of the avs file (48000 -> 44100) and allow us to enter a custom bitrate for audio as well?

Thanx.

[Atak_Snajpera]

@8ternity
Send me MediaInfo report from that .mkv.

[Discoboy]

Bluray chapters seem to be broken in 1.13.0.

If I advance chapter on standalone, it hangs, then returns to the beginning of the disc.

It worked fine in 1.12.0.:confused:

Hi Wakebrder,
Did you find the fix for this issue?
I have them same prob as you on a Panny BD35 standalone but NO probs with PowerDVD on the pc.
AVCHD movie chapters seem to be broken in 1.13.0 and 1.13.1. If I advance the chapter on BD35 standalone, it hangs, then returns to the beginning of the disc.

Its working fine on 1.12.0.

[nwg]

I have done one Blu Ray with 1.13.1 and it didn't keep the chapters. They are in 5m intervals rather than the expected original chapters.

I am going back to 1.12.0 as that worked fine for me for what I needed.

[illestdomer2005]

send me 50 mb flac or pcm sample

What do I need to use to cut it? I have the 3 channel wav file that I demuxed, and RipBot couldn't/didn't use it either.