Welcome to Doom9's Forum, THE in-place to be for everyone interested in DVD conversion. Before you start posting please read the forum rules. By posting to this forum you agree to abide by the rules. |
|
|
Thread Tools | Search this Thread | Display Modes |
5th September 2024, 20:23 | #20881 | Link |
Registered User
Join Date: Aug 2020
Location: Pennsylvania
Posts: 119
|
And just if anyone is interested, I just replace my 7950x with a 9950x. Doing a couple test runs looks like I am pushing about a 10-15% speed increase over the 7950x. Watching Ryzen Master I am also seeing about a 10 degree C decrease in cpu temp. Both were on the same 360mm Arctic 3 AIO. All I had set before with the 7950x in PBO was a hard thermal limit. Where the 7950x would top out my hard limit of 85 degrees C, the 9950x is sitting around 75C with the cpu utilization in task manager still running at 100%. I haven't changed anything in the bios after it reset everything on the CPU change, so I need to look to see if I can push things a bit more from seeing the lower temps. The 9950x is supposed to have a limit of 95C, I won't push it that much, but I think I can get a few more percent increase pushing it up so it hits that same 85C hardline i set.
I've read that the new Win11 update due out later this fall is supposed to really help boost Zen5, not sure if that is just gaming or everything, but will be interesting to see if it boosts encoding speed as well... |
6th September 2024, 13:05 | #20882 | Link |
Registered User
Join Date: Mar 2011
Posts: 434
|
Cropping
Cropping also helps with displays that are not 16:9. Some projectors screens are configured for 2.40:1 and a lot of mobile phones are around that same aspect ratio. Reverse also helps when watching 4:3 content on a 16:10 screen.
I only encode the back bars when I'm doing foreign movies and I want to push the subtitles into the black bars. |
13th September 2024, 16:08 | #20886 | Link |
German doom9/Gleitz SuMo
Join Date: Oct 2001
Location: Germany, rural Altmark
Posts: 7,028
|
Not really, MultiCoreWare released patches in batches. You might try to select a specific patch but will risk that a feature depends on several patches at the same time.
|
13th September 2024, 18:24 | #20887 | Link | |
Silent Reader
Join Date: Dec 2003
Location: Germany
Posts: 302
|
Quote:
Solution is really simple. In jobX_EncodeVideoPassX.cmd just add "--input" before the last "-" As a workaround it would be so simple even for us to add "--input -" in profiles, but then still the last "-" in cmd-file is too much and blocks executing. So for running long single machine encodes, there is no problem to manually edit the files to work. But for DE it's too much.... |
|
Yesterday, 08:00 | #20888 | Link |
German doom9/Gleitz SuMo
Join Date: Oct 2001
Location: Germany, rural Altmark
Posts: 7,028
|
I changed my x265 v4.0+4 archive.
Please note: From version 4.0 on I will build all variants without MultiView support so that they may still work without explicit --input parameter, except for a 64 bit build which has it explicitly enabled. |
Yesterday, 18:41 | #20891 | Link |
Registered User
Join Date: Sep 2023
Posts: 13
|
Encoding broke for MPEG2 Interlaced Sources
My 3 systems updated Ripbot yesterday(not entirely sure that is the culprit) and I proceeded to line up 60 or so encodes. I am encoding to HEVC and I have no issues with VC1 or H264 sources but my system is completely hung up on mpeg2 extras... specifically interlaced TFF. I unchecked all MPEG2 videos and all other encodes finished without issue. If i have deinterlace off or inverse telecine , everything works fine... AVS Meter, Preview and DE. If I select Interlaced TFF, AVS Meter shows no progress, Preview will open MPC but it will hang until I end the process, and DE will run with all servers stuck on initializing(I've also tried without DE). Full disclosure, I am also trying to track down a random BSOD (that occurs while my system is idle) so this is all 24 hours after an in place WIN 11 Reinstall keeping documents and settings. Any Ideas or suggestions?
I downloaded a fresh copy of Ripbot from the first post in this thread, copied in my .ini files and disabled update. Ran it loading my previous que and it was unable to do anything with the same file. I then re-added the file and everything seems to work again. Re-adding the file into the updated Ripbot makes no difference. So there is something in the updated tools breaking Interlaced MPEG2. Last edited by Epitaph; Yesterday at 22:45. Reason: Update/More info |
Yesterday, 23:14 | #20892 | Link | |
Registered User
Join Date: Aug 2014
Posts: 15
|
Not sure whether this is an issue with 1.27.4 but a job with specific film gets stuck each time at the end of the conversion and the job never finishes properly. I have removed and re-created the job but the issue still occurs again.
I'm stuck at this point: https://images2.imgbox.com/0e/ae/6Ig7KjDG_o.png (Waiting even for hours won't help, job won't be finished). The original source file for the job was .m2ts file (blu-ray). I muxed the source file into a mkv file and created the job again with it but the result was the same. Stuck again. My conversion settings: Video: H265 Profile: MA10 Preset: Default Tune: Default Mode: CQ CRF: 16 Crop: top 132, bottom: 132 CPU denoise: MDegrain3, Strength: 300 Audio: 5.1 FHG AAC-LC 320 Data from the source file: Quote:
|
|
Tags |
264, 265, appletv, avchd, bluray, gui, iphone, ipod, ps3, psp, ripbot264, x264 2-pass, x264 gui, x264_64, x265, xbox360 |
Thread Tools | Search this Thread |
Display Modes | |
|
|