Welcome to Doom9's Forum, THE inplace to be for everyone interested in DVD conversion. Before you start posting please read the forum rules. By posting to this forum you agree to abide by the rules. 
26th February 2021, 08:34  #1  Link 
Registered User
Join Date: Feb 2021
Posts: 4

YUV to RGB Conversion
Hello!
https://en.wikipedia.org/wiki/YUV#Co...on_to/from_RGB Can someone explain to me where from Umax and Vmax coefficients? In BT.601 and BT.709 standards nothing about this values. 
26th February 2021, 09:06  #2  Link 
Registered User
Join Date: May 2006
Posts: 3,998

You won't find Umax and Vmax in the current ITUR BT.6017 document which refers to digital TV. U,V has its roots in analog color TV. Digital systems define Cb,Cr rather than U,V.
You may find these links helpful: https://software.intel.com/content/w...ml?language=en The basic equations are Y'= 0.299*R' + 0.587*G' + 0.114*B' U'= 0.147*R'  0.289*G' + 0.436*B' = 0.492*(B' Y') V'= 0.615*R'  0.515*G'  0.100*B' = 0.877*(R' Y') With R'G'B' in the range of [0,1] the maximum value of V' becomes 0.615 (for R'G'B'=[1,0,0]), and the maximum value of U' becomes 0.436 (for R'G'B'=[0,0,1]). For the various conversion matrices see here: https://web.archive.org/web/20120403...onversion.html For analog TV the "YUV  RGB Color Format Conversion" matrix applies. In the digital realm there is no U,V, but unfortunately it is often used in exchange of Cb, Cr which is not correct. Last edited by Sharc; 27th February 2021 at 15:26. Reason: Links and clarifications added 
27th August 2021, 19:36  #3  Link 
Registered User
Join Date: Feb 2020
Posts: 541

Umax and Vmax are also present in BT.601/BT.709 standards. Both of them are set to 1/2 though. Also Umax and Vmax of old analog are defined in BT.470. There was an error made there though. 0.493 is incorrect as given there. It was too late to correct it though.
Last edited by Balling; 28th August 2021 at 15:41. 
28th August 2021, 15:40  #5  Link 
Registered User
Join Date: Feb 2020
Posts: 541

0.4926. In practice all hardware decoders used that number in a form of 1/2.03, so... that it is not Umax or Vmax and has nothing to do with 1/2 Umax=Vmax in digital standards. You confused that in previous post.
You can read it in SMPTE 170M but I will quote for you: (It should be noted that there is an apparent error in the 1953 calculations of these reduction factors. Although the calculations were performed to a high degree of precision, a luminance matrix coefficient of 0.115 was used for blue instead of the correct 0.114. This resulted in values of 0.493 and 0.877 for BY and RY, respectively. These were normally approximated to 1/2.03 and 1/1.14, respectively. The error was not significant in the equations published to an accuracy of two significant figures, but it is significant for the higher precision equations used in this standard. The values quoted below and used in this standard are derived from the correct luminance matrix.) (Lower case is used to distinguish the reduced values: by = 0.492111...(BY); (4) ry = 0.877283...(RY).) Last edited by Balling; 30th March 2023 at 09:55. 
28th August 2021, 16:22  #7  Link 
Registered User
Join Date: Feb 2020
Posts: 541

Just again. 0.5 and 0.493 are not the same values. at all. Umax and Vmax in BT.470 were 0.436 and 0.615 respectivly while in digital realm both became 0.5. Please note that NTSC further applied 33 degree rotation matrix and swapped U' and V' to get Y'IQ. So U' is Q and V' becomes I. Okay?
Last edited by Balling; 28th August 2021 at 16:29. 
14th January 2022, 09:04  #9  Link 
Registered User
Join Date: Jan 2022
Posts: 1

Hello.
I am not good at English, so I am using automatic translation. I apologize if there are any incorrect expressions. In conclusion, Umax and Umin can be derived from the following equations. Umax = (1Wb)*SQRT(((Wg/3+Wb2*Wr*Wb)*((1Wr+Wb)/3+Wb))/(Wg*(Wg+2*Wb*Wr))) Vmax = (1Wr)*SQRT(((Wg/3+Wb2*Wr*Wb)*((1Wr+Wb)/3+Wb))/(Wg*(Wg+2*Wb*Wr))) The reason for this comes from the inequality explained here on p. 107. https://drive.uqu.edu.sa/_/mskhayat/...timedia_2e.pdf This means that Y'±√(U^2+V^2) must be exactly in the range of 1/3 to 4/3. It is important to note that there is symmetry in the Y'UV space, so you only need to examine Y'+√(U^2+V^2) ≤ 4/3. Let U = Cu*(B'Y'), V = Cv*(R'Y'). The goal is to find the conditions under which the parallelepiped in Y'UV space, transferred by linear transformation of the RGB cube, fits exactly into the cone of Y'+√(U^2+V^2) = Y'+√(Cu^2*(B'Y')^2+Cv^2*(R'Y')^2) ≤ 4/3. You will soon see that you only need to test each vertex of the parallelepiped. For example, if vertex (R', G', B')=(1, 0, 0), then Y'=Wr, so the inequality is the following ellipse of Cu and Cv. Wr^2*Cu^2+(1Wr)^2*Cv^2≤(4/3Wr)^2 By finding the equations of the ellipses for the 8 vertices and examining their common parts, you can find 2 such ellipses whose overlapping parts satisfy the inequalities of the remaining 6 ellipses. The RGB values corresponding to those 2 ellipses are (1, 1, 0) and (0, 1, 1). Finally, the point where the boundaries of the 2 ellipses intersect gives Umax and Umin. (1Wb)^2*Cu^2+Wb^2*Cv^2 = (1/3+Wb)^2 Wr^2*Cu^2+(1Wr)^2*Cv^2 = (1/3+Wr)^2 Umax = Cu/(1Wb) Vmax = Cv/(1Wr) I hope this helps you. 
Tags 
conversion, rgb, yuv 
Thread Tools  Search this Thread 
Display Modes  

