CCE 2.70.02.00 and ECL?

[Harm]

Hi!
I am using DVD-RB 1.00 RC2 and I recently changed the paths to CCE SP (new) version 2.70.02.00 just like the help file tells me to. (So pointing directly to cctspt.exe instead of an ECL file). I selected CCE SP and tried to run it.
In the encode step I get an error stating: item.ecl is not a ECL for CCE SP Trial version. I included the ecl file. Should I select SP Trial or still use an ECL file?
If any of these should be the correct option maybe a warning would be nice to be implemented?

contents of item.ecl:
; Cinema Craft Encoder SP -- Encoder Control List
; Created by DVD Rebuilder

[item]
title=V01000000001001
aud_out=0
vaf_file=G:\#DVD-RB-WORK\ENIGMA\D2VAVS\V01000000001001.vaf
aud_file=G:\#DVD-RB-WORK\ENIGMA\D2VAVS\V01000000001001.mpa
file_focused=0
packet_size=2048
width=720
height=576
frame_rate_idx=3
cbr_brate=6000
vbr_brate_avg=3642
vbr_brate_min=500
vbr_brate_max=7816
seq_endcode=0
dvd=0
half_width=0
half_height=0
lum_level=0
adjust_q_matrix=0
aspect_ratio=2
gop_m=3
gop_nm=4
gop_hdr=12
seq_hdr=1
all_closed_gop=0
fix_gop_length=0
samples_per_sec=44100
stereo=2
brate_idx=7
crc=1
progressive=0
alternate_scan=1
intra_dc_prec=2
intra_dc_precision_9_max=113
intra_dc_precision_10_max=113
aud_mode=0
tc_ref_frm=0
drop_frame=0
fix_vbv_delay=0
letter_box=0
pulldown_detect=0
offset_line=0
create_new_vaf=1
credits_tweak=0
credits_start=0x00000
credits_brate=1000
h_filter=0
h_filter_idx=8
dither=0
dither_max=8
quality_prec=25
timecode=0x0000000
q_char_f=25
tc_offset=0
v_filter=0
v_filter_val=6
pict_name=
pict_type=3
pict_level=255
video_type=16
vid_file0=G:\#DVD-RB-WORK\ENIGMA\D2VAVS\V01000000001001.m2v
vid_file1=G:\#DVD-RB-WORK\ENIGMA\D2VAVS\V01000000001001.m2v
vid_out=1
vaf_out=1
opv_q_factor=20
opv_brate_min=0
opv_brate_max=7816
vbr_bias=25
vbr_pass=1
use_filter=0
filter_val=6
non_linear=1
top_first=0
mpeg1=0
mpeg1_cps=1
qmat_idx=0

[file]
name=G:\#DVD-RB-WORK\ENIGMA\D2VAVS\V01000000001001.avs
frame_first=0
frame_last=3479
encode_first=0
encode_last=3479

[jptheripper]

just b/c i have never seen it before, try dropping the # from the folder name

[Harm]

just b/c i have never seen it before, try dropping the # from the folder name
I use the # for years now. Never has been a problem. But I'll try....

[Carpo]

tell dvd-rb to use the cce sp trial setting

[Harm]

I use the # for years now. Never has been a problem. But I'll try....
Dropping the # has no effect........... I'll try SP trial setting.....

[Harm]

When using the CCE SP Trial checked option the error is gone.........

Let's hope the result will be satisfactory!!

[TheSeeker]

When using the CCE SP Trial checked option the error is gone.........

Let's hope the result will be satisfactory!!

I can almost guarantee that it will be. Except for that watermark the trial version is going to put in your video stream. I would recommend buying the basic version if you like the result of CCE SP Trial. It only supports 2 passes (all I ever do anyways), but the encode engine is essentially the same as CCE SP 2.70.

[trebor_07]

This has been discussed on many occasions before and here's the fix for it:

CCE v2.70+ works just fine with DVD-RB v0.69.

Just replace the:
; Cinema Craft Encoder SP -- Encoder Control List
; Created by DVD Rebuilder

with:
; CCE SP Trial Version -- Encoder Control List

at the top in REBUILDER.ECL