DVD2SVCD Just runs Commands..but no output of files

[SuperK]

Okay, i stole the name of the topic from the only thread i found that had any kinds of similar problems (but wasnt quite the same and didnt have a solution).

The problem, as the topic suggests, is that after dvd2svcd has done its thing i have no files from after cce does its thing, but i get no errors either, from any program after that.

I notice how every step take as long time as if the actual steps are being done (or close to it, first rips on this computer), while there is no output.
Any suggestions are very welcome, i ran out of ideas a while ago :\

WNASPI32.DLL 0.0.0.0
--------------------------------------------------------
- 6/22/2004 12:23:00 PM
- DVD to SVCD Conversion
- DVD2SVCD ver. 1.2.2 build 1
--------------------------------------------------------
Initializing
- F:\VIDEO_TS\VTS_03_0.IFO
- F:\VIDEO_TS\VTS_03_1.vob
- F:\VIDEO_TS\VTS_03_2.vob
- F:\VIDEO_TS\VTS_03_3.vob
- F:\VIDEO_TS\VTS_03_4.vob
Initializing finished.

--------------------------------------------------------
- 6/22/2004 12:23:04 PM
- Free on drive D: 45701.41 mb
- Internal rip
--------------------------------------------------------
Preparing vobfiles to be ripped:
- F:\VIDEO_TS\VTS_03_1.vob
- F:\VIDEO_TS\VTS_03_2.vob
- F:\VIDEO_TS\VTS_03_3.vob
- F:\VIDEO_TS\VTS_03_4.vob

Ripping: F:\VIDEO_TS\VTS_03_1.vob
Ripping: F:\VIDEO_TS\VTS_03_2.vob
Ripping: F:\VIDEO_TS\VTS_03_3.vob
Ripping: F:\VIDEO_TS\VTS_03_4.vob
Ripping finished. Speed: 5629

--------------------------------------------------------
- 6/22/2004 12:34:43 PM
- DVD2AVI
--------------------------------------------------------
Creating DVD2AVI INI file:
- E:\Program Files\DVD2SVCD\DVD2AVI\DVD2AVI.INI

Variable settings:
iDCT_Algorithm: 32-bit SSE MMX

Executing DVD2AVI.
Executing DVD2AVI. Commandline:
"E:\Program Files\DVD2SVCD\DVD2AVI\DVD2AVI.exe" -CS=2 -YR=1 -OM=0 -EXIT -OF=[D:\dvd2svcd\DVD2AVI_Project_file] -IF=[D:\dvd2svcd\VTS_03_1.vob,D:\dvd2svcd\VTS_03_2.vob,D:\dvd2svcd\VTS_03_3.vob,D:\dvd2svcd\VTS_03_4.vob]
Analyzing DVD2AVI Project file
Force Film NOT activated!
Framerate: 29970
DVD2AVI processing done.

--------------------------------------------------------
- 6/22/2004 12:38:02 PM
- Free on drive D: 41863.84 mb
- AUDIO Extraction
--------------------------------------------------------
Found AC3 stream id: 0x80
Filename: D:\dvd2svcd\Extracted_audio_1.ac3
Audio1 delay: -67 ms
Audio extraction finished.


Encoding Audio. Filename: D:\dvd2svcd\Extracted_audio_1.ac3
Executing BeSweet. Commandline:
"E:\Program Files\DVD2SVCD\BeSweet\BeSweet.exe" -core( -input "D:\dvd2svcd\Extracted_audio_1.ac3" -output "D:\dvd2svcd\Encoded_audio_1.mp2" -logfile "D:\dvd2svcd\Encoded_audio_1.log" ) -azid( -L -3db -l 0db -c normal -s surround -g max ) -ota( -d -67 ) -shibatch( --rate 44100 ) -2lame( -e -b 224 -m s )
Audio conversion of D:\dvd2svcd\Extracted_audio_1.ac3 finished.

Audio conversion finished.

--------------------------------------------------------
- 6/22/2004 1:28:00 PM
- Free on drive D: 41507.31 mb
- Video Encoding using Cinema Craft
--------------------------------------------------------

Executing Cinema Craft Encoder.
Error cannot find CCE project file.
Closing program
CCE Max Speed: 0.490
Video Encoding finished.

--------------------------------------------------------
- 6/22/2004 5:56:01 PM
- Free on drive D: 36090.15 mb
- Converting Pictures from ES to PS
--------------------------------------------------------
Saving bbMPEG settings: E:\Program Files\DVD2SVCD\bbMPEG\default.ini
--------------------------------------------------------
- 6/22/2004 5:56:03 PM
- Free on drive D: 36090.15 mb
- Converting Pictures from ES to PS
--------------------------------------------------------
Saving bbMPEG settings: E:\Program Files\DVD2SVCD\bbMPEG\default.ini
--------------------------------------------------------
- 6/22/2004 5:56:06 PM
- Free on drive D: 36090.15 mb
- Converting Pictures from ES to PS
--------------------------------------------------------
Saving bbMPEG settings: E:\Program Files\DVD2SVCD\bbMPEG\default.ini
--------------------------------------------------------
- 6/22/2004 5:56:09 PM
- Free on drive D: 36090.15 mb
- Multiplexing and cutting
--------------------------------------------------------
Saving bbMPEG settings: E:\Program Files\DVD2SVCD\bbMPEG\default.ini
Offset in Seconds: 1
Executing bbMPEG.
Variable Settings:
Movie offset: 1 seconds
Cut point: 800 mb

Executing RunbbMPEG. Commandline:
"E:\Program Files\DVD2SVCD\bbMPEG\RunbbMPEG.exe" "D:\dvd2svcd\bbMPEG_Muxed_File.mpg"
Multiplexing and cutting finished.

--------------------------------------------------------
- 6/23/2004 12:24:10 AM
- Free on drive D: 36090.14 mb
- Determining length of audio
--------------------------------------------------------
Analyzing finished.

Image creation finished.

--------------------------------------------------------
- 6/23/2004 12:24:19 AM
- Free on drive D: 36090.13 mb
- Conversion done!
--------------------------------------------------------

[Nick]

Hello. Welcome to the forums and congratulations on a fine first post!

From the log, the two things that leap out are

1. Probably unrelated but you do not appear to have the relevant aspi drivers installed. You can get these from the dvd2dvd.org homepage.

2. Your version of CCE looks as if it may not support ecl files (necessary!). What version of CCE are you using? CCE SP or CCE Basic and which version number?

[SuperK]

Thanks, Nick. Ill try to answer your questions.

1. I noticed the same with the aspi drivers version (it was metioned in the other thread i found), but i watched the process and the vobs does get ripped, so i didnt think any more about that. I can try installing the drivers and doing it over though.

2.EDIT : The version im using is CCE SP v2.67.00.11.


Anyways, thanks for you help and suggestions.


EDIT: Sorry, i knew it was kinda against the rules but tried to get the point across without actually saying it.
And thanks for the tip, ill look into it :)

[bobwillis]

SuperK,

You require eclCCE (do a search) in order to process .ecl files. It is available from this forum.

Regards,
Bob

[SuperK]

Thanks bob, it seems to have done its trick, dunno for sure yet since my comp crached on account of low mem (been running it for a few weeks before i tried), but atleast the encode seemed to start and such.