GelberDrache
2nd April 2017, 16:01
Hi Folks,
A short overview of what i’m doing so far:
I’m running OBS Studio, trying to stream and record at the same time.
Therefor I am using a bitrate of 2500 kbit/s and the preset “Very Fast” at 720p@50.
The recording is done at 1152p@50.
My setup runs a I7-3930k and I have to watch (differs by the game I play) the CPU’s load that it does not reach 100%. With this circumstances in mind, i was thinking about to set the preset to “Ultra Fast”. I made a test recording and discovered, by a CRF of 18, that it creates “squares”. From my point of view CRF prevent those squares to appear.
And there is my question:
Is there a possibility to get the load off of the CPU (as far as possible) and prevent squares?
I hesitate to go with a CRF of 10.
Encoding settings : cabac=0 / ref=1 / deblock=0:0:0 / analyse=0:0 / me=dia / subme=0 / psy=1 / psy_rd=1.00:0.00 / mixed_ref=0 / me_range=16 / chroma_me=1 / trellis=0 / 8x8dct=0 / cqm=0 / deadzone=21,11 / fast_pskip=1 / chroma_qp_offset=0 / threads=18 / lookahead_threads=3 / sliced_threads=0 / nr=0 / decimate=1 / interlaced=0 / bluray_compat=0 / constrained_intra=0 / bframes=0 / weightp=0 / keyint=100 / keyint_min=10 / scenecut=0 / intra_refresh=0 / rc=crf / mbtree=0 / crf=18.0 / qcomp=0.60 / qpmin=0 / qpmax=69 / qpstep=4 / ip_ratio=1.40 / aq=0
picture:https://abload.de/img/doomcrf18uescv.png
You can get a look on it at the picture. It’s in the lower part in the darker areas and above the blue hp-bar.
A short overview of what i’m doing so far:
I’m running OBS Studio, trying to stream and record at the same time.
Therefor I am using a bitrate of 2500 kbit/s and the preset “Very Fast” at 720p@50.
The recording is done at 1152p@50.
My setup runs a I7-3930k and I have to watch (differs by the game I play) the CPU’s load that it does not reach 100%. With this circumstances in mind, i was thinking about to set the preset to “Ultra Fast”. I made a test recording and discovered, by a CRF of 18, that it creates “squares”. From my point of view CRF prevent those squares to appear.
And there is my question:
Is there a possibility to get the load off of the CPU (as far as possible) and prevent squares?
I hesitate to go with a CRF of 10.
Encoding settings : cabac=0 / ref=1 / deblock=0:0:0 / analyse=0:0 / me=dia / subme=0 / psy=1 / psy_rd=1.00:0.00 / mixed_ref=0 / me_range=16 / chroma_me=1 / trellis=0 / 8x8dct=0 / cqm=0 / deadzone=21,11 / fast_pskip=1 / chroma_qp_offset=0 / threads=18 / lookahead_threads=3 / sliced_threads=0 / nr=0 / decimate=1 / interlaced=0 / bluray_compat=0 / constrained_intra=0 / bframes=0 / weightp=0 / keyint=100 / keyint_min=10 / scenecut=0 / intra_refresh=0 / rc=crf / mbtree=0 / crf=18.0 / qcomp=0.60 / qpmin=0 / qpmax=69 / qpstep=4 / ip_ratio=1.40 / aq=0
picture:https://abload.de/img/doomcrf18uescv.png
You can get a look on it at the picture. It’s in the lower part in the darker areas and above the blue hp-bar.