PDA

View Full Version : MeGui missing directory?

clutch
19th August 2006, 12:31
I'm trying out MeGui for the first time starting yesterday so maybe I just missed installing something. I seem to be missing an 'extra' directory.

The version is 0.2.3.2192 which must have been updated during the update process since I downloaded 0.2.3.2177.

The only update that didn't go right is the neroaacenc which I hope isn't the problem since I read that there is problems offering it until Nero gives their blessing.

Scanning my computer, I don't see a single .cqm file anywhere.

I found this thread: http://forum.doom9.org/showthread.php?p=861339&highlight=SixOfNine.cqm#post861339
That I hoped would help but I have to find the directory to give the full path to it.

I attached excerpts of logs below.

Thanks for any help.

Clutch

------------------------------------------------------
Log for job job2-1

xvid_encraw - raw mpeg4 bitstream encoder written by Christoph Lampert 2002-2003

Error opening input file extra\Didees SixOfNine.cqm

------------------------------------------------------

Log for job job3-1

xvid_encraw - raw mpeg4 bitstream encoder written by Christoph Lampert 2002-2003

Error opening input file extra\eqm_v3ulr_rev3.xcm

-----------------------------------------------------
Sharktooth
19th August 2006, 14:07
The problem are the xvid profiles. They were made with relative paths.
You should point MeGUI to the right place where you have downloaded the CQMs.
clutch
19th August 2006, 20:05
The problem are the xvid profiles. They were made with relative paths.
You should point MeGUI to the right place where you have downloaded the CQMs.


That must be the problem. Where do I download the .cqm's?

Thanks,

Clutch
Sharktooth
20th August 2006, 03:53
search the forum or maybe ask in the xvid board.
Bh4i
21st August 2006, 09:05
I was also getting the same error..
So its a problem with the xvid profiles. First time using MeGUI for xvid :)
crazybond
29th August 2006, 14:25
I'm trying out MeGui for the first time starting yesterday so maybe I just missed installing something. I seem to be missing an 'extra' directory.

The version is 0.2.3.2192 which must have been updated during the update process since I downloaded 0.2.3.2177.

The only update that didn't go right is the neroaacenc which I hope isn't the problem since I read that there is problems offering it until Nero gives their blessing.

Scanning my computer, I don't see a single .cqm file anywhere.

I found this thread: http://forum.doom9.org/showthread.php?p=861339&highlight=SixOfNine.cqm#post861339
That I hoped would help but I have to find the directory to give the full path to it.

I attached excerpts of logs below.

Thanks for any help.

Clutch


------------------------------------------------------

Log for job job3-1

xvid_encraw - raw mpeg4 bitstream encoder written by Christoph Lampert 2002-2003

Error opening input file extra\eqm_v3ulr_rev3.xcm

-----------------------------------------------------


even i faced same error..when 1st used megui for Xvid...see here the link http://www.webalice.it/f.corriga/CQMs/eqm_v3ulr_rev3.xcm
make folder in ur in xvid_encraw folder called extra n put the file in that frm the link given above...

hope this helps as this solved the same error that i got...

regards
check
29th August 2006, 14:52
As to neroaacenc, you can download that from here: ftp://ftp6.nero.com/tools/NeroDigitalAudio.zip
spanky123
26th December 2006, 16:08
http://www.webalice.it/f.corriga/CQMs/eqm_v3ulr_rev3.xcm
make folder in ur in xvid_encraw folder called extra n put the file in that frm the link given above...

hope this helps as this solved the same error that i got...

regards

It was fine for me just yesterday. Then something started goin wrong. I got nfi what.

But that file you provided fixed it all now. Thanks